Introduction:
On a fresh morning, you never want to waste your time reading a newspaper struggling with a broken toilet handle. It may be a common scenario that you are facing problems with the mechanism of handling your chainless toilet flusher. But you don’t need to bother if you know How to fix a toilet handle that has no chain.
Here you will have a proper direction of handling the chainless Mansfield toilet and pressure-assisted toilet. You don’t need to worry about manual repair or replacement of the lever of the traditional toilet. Let’s dive deeper to sort out the problem.
How to fix a toilet handle that has no chain
While you are determined to fix the toilet handle manually you have to find out the types of flapper. Once you can detect the problem you just need to follow the given instruction. There are some easy methodologies to follow that will help to make your effort work.
Lever armed toilet handle replacement:
You don’t find a lift up the chain in a Mansfield toilet rather you may get a flapper. The flapper is an adjustable circular disk with which the water is sealed in the tank after refill. To get rapid water passing the disk needs to open up.
But somehow the seal stuck up and the handle demands harder force while pushing. And it leads the toilet handle broken down as most of the time it is made of fragile plastic. But the relaxing matter is you can manage a toilet handle replacement easily in your nearby hardware shop within a few costs. Now if you know how to fix a toilet handle that stays down you can easily fix it by yourself.
The steps to replace toilet handle:
Step-01: Uncovering the tank
First of all, you have to open up the Lid cover of the water tank to find out the plastic nut. You can unscrew the nut by hand. If it seems hard you can use a wrench to move it in clockwise and unroot it.
Step-02: Detaching the arm and the flapper
It’s time to depart the end of the arm of the handle that is connected to the flapper rod. Now you have to pull out the handle to remove it from the previous setting.
Step-03: Inserting the new handle
Once you have removed the entire handle successfully the tank is ready to get a new handle arm assembly. Now you have to go through the reverse action of removing it. Slide the nut at the end of the handle and hook the other lever under the flapper rod. You can fix and tighten the nut by turning it in the anticlockwise direction.
Solution for poor pressure-assist flushing:
There are some common designs of toilets that don’t provide any flapper or chain. Those toilets are made by following a different pressure-assist flushing mechanism as it is considered the most convenient flushing system. You will get a flash button on the top of the tank.
In these types of toilets tank, you will get a sealed content bowl with an amount of air pressure. When the tank gets refilled, the air gets compressed. if you push on the top-bottom the air pressure creates inside the tent. A valve will open immediately and the water flows quickly through the channel with a louder sound.
The problem you may face in handling pressure-assisted flushing toilets is the supply of poor water pressure. To overcome the trouble, you must know How to replace chainless toilet handle.
Steps to replace the damage:
Step-01: Stop the supply of the water:
In order to fix the problem of poor water pressure, you have to disconnect the water supply to check the actual pressure. It should be above one gallon within one minute. If it has not happened check inlet tubing for debris. Whether it creates obstacles in the smooth flow of water.
Step-02:Check the air pressure
Secondly, you have to examine the air pressure inside the tank. It is a small aperture situated on the vertical tube of the tank. Now you have to pour a very small amount of water on the hole and let it be flushed.
Step-03: Clean the Screen
Notice the water whether it is consumed by the aperture or not. If not, you have to unscrew the cap to trace out the screen. Clean the screen carefully so that no debris is left aside. check it well if there are any necessities of replacing the screen.
Step -04: Fixing the armature
It’s time to connect the armature with the flush button so that it can create pressure on the rod of the flush cartridge. Fix it tightly in the right place.
Step -05: Replacing the O-ring
You may face problems sometimes due to the failure of the action properly.
If so, just unplug the actuator. By removing the flush cartridge replace the O-rings. Finally, check out the leaks and repair them.
Conclusion:
Now all the steps and proceeding techniques are in your hand. It is a common scenario that you may face trouble with a broken toilet Lever. Don’t let the issue pinch your head for long as you can solve it by yourself. If you have got a clear idea about How to fix a toilet handle that has no chain you don’t need to face any unwanted hazardous in the toilet. Just follow the instructions and overcome the problem within a few minutes.
FAQ:
Why does my toilet not have a chain?
The difference in the design defines the use of chain in a toilet or not. If your toilet is a Mansfield toilet or pressure-assist toilet it would not have a chain or flapper.
Do all toilet handles fit all toilets?
The simple answer is no. there is a vast range of handles which is specially manufactured for particular types of the toilet tank. So, you have to buy the handle in accordance with the mechanism of the previous toilet handle.
How do you fix a toilet without a chain?
To fix a toilet without a chain you open up the tank. then you have to Detach the arm and the flapper and keep the assembly apart. Now you can replace the new handle and adjust it in the toilet tank
Can a toilet handle be replaced?
Your toilet handle can be replaced with another handle. If it gets broken you can’t flush water into the toilet. You need to focus on the instructions and fix them appropriately.
META:
To get relief from the issue of a problematic chainless handle in a toilet, you must know how to fix a toilet handle that has no chain and manage to get a nonstop supply of water at the toilet.